Buy Lutron RadioRA 2 Dimmers for Your Home Lighting System

RA2 Dimmers

 When starting out on a RA 2 dimmer installation there are a few important facts to note. All dimmers and on/off switches have to be hard             wired to your lighting loads and it is vital to match the appropriate dimmer to the lighting types that is being controlled. The Dimmers                   receive RF signals from a variety of master controllers which in turn controls your lighting. These commands come from in wall and                   tabletop keypads, from Pico controllers, smart phone and tablets. Plus "voice control" is becoming very important within the home.

 

 

image© 2020 Lutron Electronics

 

 "Matching the correct dimmer to the lighting type is vital in order to ensure performance"

 1000 Watt dimmer   # RRD-10D     incandescent / magnetic low voltage, loads over 600 watts

 1000 Watt dimmer  # RRD-10ND   incandescent / magnetic low voltage, neutral based dimmer. 

 on/off switch switch # RRD-8ANS  8 amp on/off switch no dimming

 Bulbs tested and approved by Lutron to work with their dimmers.                   

           For a list of compatible bulbs click on this link

                         Click here to visit Lutrons approved Lighting bulbs

            

     

   



 

Lutron have upgraded their dimmer offering for both the full RA 2 and RA 2 Select.                Both Lighting Systems now use the two dimmers RRD-6ND and RRD-PRO shown below.       

image© 2020 Lutron Electronic

Led neutral based dimmer part # RRD-6ND

This RA 2 neutral based dimmer will handle up to 600 watts of  incandescent, magnetic LV and 150 watts of led. It will not work on Electronic lighting. Please make sure that the bulbs being used have been tested and approved by Lutron otherwise it becomes "buy it and try it technology"

Led dimmer for all lighting loads part # RRD-PRO

This new dimmer automatically adapts to the load type by providing control for a wider variety of lighting fixtures. This dimmer has an almost universal application for lighting types such as: Incandescent, Halogen, Electronic Low Voltage, Magnetic Low Voltage and of course dimmable led's (neutral wire optional) the pro dimmer is a solid performer for most led lights. 

250 W CFL / LED , 500 W Incandescent / Halogen / ELV, 400 VA MLV Phase Selectable

Here is a sample pack of these two dimmers to test out first before a full installation

 
                                            
                              

 

 

 

                               Do you have a neutral wire ? find out now and why you may need one.

                                          

                                                                         

                                                                   

 

Tabletop lamp Dimmer module        part # RRD-3LD-WH


Allows the control of one plug-in lamp (2 prong only) as part of a RadioRA 2 System. Lights fade up or down over 3 seconds when turned on or off. Double tap brings lights to full on. Plugs into a standard wall outlet. Load Type: Incandescent and Magnetic LV, for table and floor lamps maximum 300 watts. Some high grade leds' work well

Tabletop lamp Dimmer module        part # RR-3PD-1-SW

Allows the control of one plug-in lamp (2 prong only) as part of a RadioRA 2 System. Lights fade up or down over 3 seconds when turned on or off. Double tap brings lights to full on. Plugs into a standard wall outlet. Load Type: Incandescent and Magnetic LV, some dimmable led bulbs for table and floor lamps maximum 300 watts.

Plug in appliance switch module     part # RR-15APS-1-SW

RadioRA 2 RF Plug-in switch module allow general purpose switching loads to be added to a system quickly and easily using Lutrons Clear Connect RF Technology. These modules can be hidden behind furniture or appliances. 

                                 

                   RRD-3LD-WH                                         RR-3PD-1-SW                             RR-15APS-1-SW